Welder.Certificate.Welder (Certified)
Competency | Competency Requirements | Upload Requirements | Examples |
Hot Work.Training.Hot Work Permit Training | Hot Work Permit Training All affected personnel that are required to complete, approve, issue or reissue Hot Work Permits should be trained on multiple aspects of the permitting system and Hot Work activities. OSHA Reference: Construction 29 CFR 1926 Subpart J, 1926.350, 1926.351, 1926.352, 1926.353, 1926.354 All affected personnel that are required to complete, approve, issue or reissue Hot Work Permits should be trained on multiple aspects of the permitting system and Hot Work activities. This training is recommended Annually or when any changes occur to the Hot Work Permit system and/or hot work activities. The following OSHA regulations are applicable to construction hot work: 1926 Subpart J - Welding and Cutting; 1926.350 - Gas Welding and Cutting; 1926.351 - Arc Welding and Cutting; 1926.352 - Fire Prevention; 1926.353 - Ventilation and Protection in Welding, Cutting, and Heating; 1926.354 - Welding, Cutting, and Heating in Way of Preservative Coatings. | OSHA Reference: Construction 29 CFR 1910 Subpart Q, 1926 Subpart J, 1926.350, 1926.351, 1926.352, 1926.353, 1926.354 The training documentation uploaded should be dated within the 12 months. Acceptable training documentation should include the following: Subject/Topic of the Training Training documentation can be in the form of a: Certificate | |
Welder.Certificate.Welder (Certified) OSHA Reference: 1910.252 General Requirements (a) Fire prevention and protection (2) Special precautions. When the nature of the work to be performed falls within the scope of paragraph (a)(1)(ii) of this section certain additional precautions may be necessary: (xiii) Management. Management shall recognize its responsibility for the safe usage of cutting and welding equipment on its property and: (C)Insist that cutters or welders and their supervisors are suitably trained in the safe operation of their equipment and the safe use of the process. | |||
Welder Certification – Arc welding & cutting | OSHA Reference: 1910.254 - Arc Welding & Cutting (a) General (3) Instruction. Workmen designated to operate arc welding equipment shall have been properly instructed and qualified to operate such equipment as specified in paragraph (d) of this section. | OSHA Reference: General Industry 29 CFR 1910.253 The training documentation uploaded should be dated within the 6 months and/or current and within 6 months of expiration Acceptable training documentation should include the following: Subject/Topic of the Training Training documentation can be in the form of a: Certificate or equivalent | |
Welder Certification – Oxygen-fuel gas welding & cutting | OSHA Reference: 1910.253 - Oxygen-Fuel Gas Welding and Cutting (a) General requirements (4) Personnel. Workmen in charge of the oxygen or fuel-gas supply equipment, including generators, and oxygen or fuel-gas distribution piping systems shall be instructed and judged competent by their employers for this important work before being left in charge. Rules and instructions covering the operation and maintenance of oxygen or fuel-gas supply equipment including generators, and oxygen or fuel-gas distribution piping systems shall be readily available. | OSHA Reference: General Industry 29 CFR 1910.253 The training documentation uploaded should be dated within the 6 months and/or current and within 6 months of expiration Acceptable training documentation should include the following: Subject/Topic of the Training Training documentation can be in the form of a: Certificate or equivalent | |
Welder Certification – Resistance welding | OSHA Reference: 1910.255 - Resistance Welding (a) General (3) Personnel. Workers designated to operate resistance welding equipment shall have been properly instructed and judged competent to operate such equipment. | OSHA Reference: General Industry 29 CFR 1910.253 The training documentation uploaded should be dated within the 6 months and/or current and within 6 months of expiration Acceptable training documentation should include the following: Subject/Topic of the Training Training documentation can be in the form of a: Certificate or equivalent |