Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

Version 1 Next »

Competency

Competency Requirements

Upload Requirements

Examples

Hot Work Permit Training

Hot Work Permit Training
OSHA Reference: General Industry 29 CFR 1910 Subpart Q

All affected personnel that are required to complete, approve, issue or reissue Hot Work Permits should be trained on multiple aspects of the permitting system and Hot Work activities.

OSHA Reference: Construction 29 CFR 1926 Subpart J, 1926.350, 1926.351, 1926.352, 1926.353, 1926.354

All affected personnel that are required to complete, approve, issue or reissue Hot Work Permits should be trained on multiple aspects of the permitting system and Hot Work activities. This training is recommended Annually or when any changes occur to the Hot Work Permit system and/or hot work activities. The following OSHA regulations are applicable to construction hot work: 1926 Subpart J - Welding and Cutting; 1926.350 - Gas Welding and Cutting; 1926.351 - Arc Welding and Cutting; 1926.352 - Fire Prevention; 1926.353 - Ventilation and Protection in Welding, Cutting, and Heating; 1926.354 - Welding, Cutting, and Heating in Way of Preservative Coatings.

OSHA Reference: Construction 29 CFR 1910 Subpart Q, 1926 Subpart J, 1926.350, 1926.351, 1926.352, 1926.353, 1926.354

The training documentation uploaded should be dated within the 12 months.

Acceptable training documentation should include the following:

Subject/Topic of the Training
Instructor Name
Employee Name
Employee Signature
Date

Training documentation can be in the form of a:

Certificate
Safety Meeting/Toolbox Talk
Refresher Training

Welder (Certified)

Welder Certification
OSHA Reference: 1910.252 General Requirements

(a) Fire prevention and protection (2) Special precautions. When the nature of the work to be performed falls within the scope of paragraph (a)(1)(ii) of this section certain additional precautions may be necessary: (xiii) Management. Management shall recognize its responsibility for the safe usage of cutting and welding equipment on its property and: (C)Insist that cutters or welders and their supervisors are suitably trained in the safe operation of their equipment and the safe use of the process.

OSHA Reference: General Industry 29 CFR 1910.253

The training documentation uploaded should be dated within the 6 months and/or current and within 6 months of expiration

Acceptable training documentation should include the following:

Subject/Topic of the Training
Instructor Name
Employee Name
Employee Signature
Date

Training documentation can be in the form of a:

Certificate or equivalent

Welder Certification – Arc welding & cutting

OSHA Reference: 1910.254 - Arc Welding & Cutting

(a) General (3) Instruction. Workmen designated to operate arc welding equipment shall have been properly instructed and qualified to operate such equipment as specified in paragraph (d) of this section.

OSHA Reference: General Industry 29 CFR 1910.253

The training documentation uploaded should be dated within the 6 months and/or current and within 6 months of expiration

Acceptable training documentation should include the following:

Subject/Topic of the Training
Instructor Name
Employee Name
Employee Signature
Date

Training documentation can be in the form of a:

Certificate or equivalent

Welder Certification – Oxygen-fuel gas welding & cutting

OSHA Reference: 1910.253 - Oxygen-Fuel Gas Welding and Cutting

(a) General requirements (4) Personnel. Workmen in charge of the oxygen or fuel-gas supply equipment, including generators, and oxygen or fuel-gas distribution piping systems shall be instructed and judged competent by their employers for this important work before being left in charge. Rules and instructions covering the operation and maintenance of oxygen or fuel-gas supply equipment including generators, and oxygen or fuel-gas distribution piping systems shall be readily available.

OSHA Reference: General Industry 29 CFR 1910.253

The training documentation uploaded should be dated within the 6 months and/or current and within 6 months of expiration

Acceptable training documentation should include the following:

Subject/Topic of the Training
Instructor Name
Employee Name
Employee Signature
Date

Training documentation can be in the form of a:

Certificate or equivalent

Welder Certification – Resistance welding

OSHA Reference: 1910.255 - Resistance Welding

(a) General (3) Personnel. Workers designated to operate resistance welding equipment shall have been properly instructed and judged competent to operate such equipment.

OSHA Reference: General Industry 29 CFR 1910.253

The training documentation uploaded should be dated within the 6 months and/or current and within 6 months of expiration

Acceptable training documentation should include the following:

Subject/Topic of the Training
Instructor Name
Employee Name
Employee Signature
Date

Training documentation can be in the form of a:

Certificate or equivalent

  • No labels